SST Profibus Backplane Products Installation v3.1

安裝文件下載：僅提供個人在家學習用途，此程序文件來源于網絡可靠性穩定性完整性皆無法驗證，禁止用于其他用途，否則后果自負。
PB3_Backplane_Install_V3_1_0.zip (78.17 MB, 售價: 25 E幣)

2025-1-16 23:49 上傳

點擊文件名下載附件
售價: 25 E幣  [記錄]  [購買]

******************************************************************************************
SST Profibus Backplane Products Installation v3.1.x.0 Content
******************************************************************************************
*************************************************************
What is New :
- Support for the SST-PB3-PCIe-H (Master/Slave), SST-PB3M-PCie-H (Master Only)
- Updated firmware pfb3-2.ss3 vv3.1.0.0
- New Slave GSD file for SST-PB3-PCIe-H

******************************************************************************************
Supported Operating Systems
******************************************************************************************
- Microsoft Windows XP Professional   32-Bit
- Microsoft Windows Server 2003        32-Bit
- Microsoft Windows Vista                32-Bit and 64-Bit
- Microsoft Windows Server 2008        32-Bit
- Microsoft Windows 7                32-Bit and 64-Bit
- Microsoft Windows Server 2008 R2        64-Bit
- Microsoft Windows Server 2012 64-Bit
- Microsoft Windows 8                32-Bit and 64-Bit
- Microsoft Windows 8.1                32-Bit and 64-Bit
******************************************************************************************
Notice
******************************************************************************************
- If you are using Windows XP and the Firewall is enabled, configure an exception to be able to use the SST Profibus Configuration Tool to browse using Ethernet/IP Driver.

******************************************************************************************
Known Issues
******************************************************************************************
SST Profibus Configuration Tool
For SST-PB3-REM, SST-PB3-REM-R Profibus Masters
- when upload config with BIT definition the bit definition is then lost
- Recommended RPI should start at 3ms for SST-PB3-REM and SST-PB3-REM-R (Currently 2ms under the Master properties on the Parameters tab)
For the SST-PB3-CPX Master
- Cannot connect to CompactLogix PLCs using a Local 1769 Bus Adapter VA1769/A (older CPX PLCs like L35E, L32E, L23E)
- Config tool is not saving the RSlinx connection type under COM Channel dialog under Master properties

SST-PB3-CLX firmware , Backplane module version 8.8.2, Profibus module version 7.29

- Get "Error: 0x2000060B. DPV1 already initialized" when do network browse in CommDTM with PB3-CLX
- Cannot resend DPV1 CIP messages when FDL errors occur
- Cannot detect all modules from slave (with more than 32 modules) when the master goes to browse for it on the network using DPView (Part of SST-Profibus Configuration Tool)

CommDTM v1.3.0.0 for SST-PB3-CLX

- the CommDTM and SST Profibus configuration Tool cannot access to the SST-PFB-CLX simultaneously.
- two CommDTM cannot access to the same SST-PFB-CLX.
- errors can occur when connecting simultaneously the CommDTM to a SST-PFB-CLX via a local path and a
SST-PFB-CLX via an Extended Path in a same ControlLogix. It is then recommended to use either local path(s), either extended path(s).

SST-PB3-REM firmware v1.1.8.0, SST-PB3-REM-R firmware v1.1.3.0
-At 10Mb H/F packets dropped.10 Mb H/F not supported
- EO (Connection accepted when Data IO size defined in the SST Profibus Configuration Tool is higher than the IO assembly size).

SST-PB3-CPX firmware v1.1.0.0
- SST-PB3-CPX module does not appear in RSlinx until a backplane connection is made to module
- Some Diagnostic counters still continue to increment when profibus cable is disconnected from Module
- Configuration Mismatch occurs when CFG tool reconnects to module that has just started up
- the option "Major Fault on Controller if connection fails While in Run mode" must not be enabled in I/O connection
- PB3-CPX module does not go CLEAR mode when CPX processor is removed from PLC

【必讀】版權免責聲明

1、本主題所有言論和內容純屬會員個人意見，與本論壇立場無關。2、本站對所發內容真實性、客觀性、可用性不做任何保證也不負任何責任，網友之間僅出于學習目的進行交流。3、對提供的數字內容不擁有任何權利，其版權歸原著者擁有。請勿將該數字內容進行商業交易、轉載等行為，該內容只為學習所提供，使用后發生的一切問題與本站無關。 4、本網站不保證本站提供的下載資源的準確性、安全性和完整性;同時本網站也不承擔用戶因使用這些下載資源對自己和他人造成任何形式的損失或傷害。 5、本網站所有軟件和資料均為網友推薦收集整理而來，僅供學習用途使用，請務必下載后兩小時內刪除，禁止商用。6、如有侵犯你版權的，請及時聯系我們（電子郵箱1370723259@qq.com）指出，本站將立即改正。