Catapult DNP3 Driver v11.0.73.17712

支持windows8.1和windows10操作系統，另外還支持Windows 2016/2019/2012R2. 對windows 7操作系統兼容性未知。
兼容的SCADA Systems：iFIX 6.0/6.1/5.9/5.8 和CIMPLICITY 11.0/10.0/9.5/9.0
安裝方法：解壓后，如果系統里沒有安裝vcredist_x86_11-0-61030.exe先安裝這個文件
下載鏈接：
百度網盤下載鏈接.txt (754 Bytes, 售價: 100 E幣)

2023-9-18 14:33 上傳

點擊文件名下載附件
售價: 100 E幣  [記錄]  [購買]

注意：請確保您所用的網絡可以訪問百度網盤并能熟練使用百度網盤下載文件，若附件內下載鏈接失效不能下載，可以回復本文留下郵箱給您發送可用鏈接。
The Catapult DNP3 driver supports DNP 3.0 master communications for up to 1,000 DNP 3.0 slave devices, across 200 serial and/or IP channels.  The driver operates as an OPC server for any control system that supports OPC.
In addition to being an OPC server, the driver is also a native GE Digital iFIX or CIMPLICITY driver, using a native interface to iFIX or CIMPLICITY systems.

General

Supports DNP 3.0 to Level 3 for both Requests and Responses
Sequence of Events (DNP Level 3 only)
Report by exception (DNP Level 3 only)
Slave supported DNP levels 1, 2, 3
Internet Protocol - both UDP and TCP
Serial (300-57600 baud)
Radio support includes Flow control; Push To Talk control; Pre & Post-transmission delay setting; configurable retries and timeouts
DCOM is not currently supported,  the driver must run on the SCADA server

DNP3.0 for iFIX
Database addressing supports both IFIX (NIO) and OPC interfaces
The Driver can be started as a standard iFIX driver through the SCU, or configured to run as a windows background service.

DNP3.0 for CIMPLICITY
Database addressing supports both CIMPLICITY and OPC interfaces
The Driver can be started as a standard CIMPLICITY driver.

Devices & Channels
Separate configuration of devices and channels
Each device can be connected to one or more channels
Each channel can be connected to one or more devices
Prioritization and automatic fail over when multiple channels are available
The maximum number of channels and devices is limited by system resources. The driver has been tested up to 1,000 devices and 200 channels.

Sequence of Events (SOE)
SOE Level 3 time mode, supporting Local and UTC time
Each and every SOE detected and written to the SOE log file, time stamped to 1msec using time captured by the I/O device
Includes time synchronization
Full support for SOE event display in iPower SCADA

Momentary Change Detect
Momentary changes (e.g. closed>open>closed) can be captured and passed on to the SCADA system, regardless of master polling cycle speed.
Each momentary change is time stamped as it was captured by the I/O device, providing an accurate record of the change.

Configuration
”On the fly” configuration without requiring system restart

Logging
Communications monitoring in configuration window and to file Logging of raw binary data (data link) and decrypted data (application layer)
Comprehensive statistics for both devices and channels
Separate SOE log file
All statistics are available to SCADA
This electronic help provides descriptive material and specific operating procedures for performing all common tasks.

【必讀】版權免責聲明

1、本主題所有言論和內容純屬會員個人意見，與本論壇立場無關。2、本站對所發內容真實性、客觀性、可用性不做任何保證也不負任何責任，網友之間僅出于學習目的進行交流。3、對提供的數字內容不擁有任何權利，其版權歸原著者擁有。請勿將該數字內容進行商業交易、轉載等行為，該內容只為學習所提供，使用后發生的一切問題與本站無關。 4、本網站不保證本站提供的下載資源的準確性、安全性和完整性;同時本網站也不承擔用戶因使用這些下載資源對自己和他人造成任何形式的損失或傷害。 5、本網站所有軟件和資料均為網友推薦收集整理而來，僅供學習用途使用，請務必下載后兩小時內刪除，禁止商用。6、如有侵犯你版權的，請及時聯系我們（電子郵箱1370723259@qq.com）指出，本站將立即改正。